Working on a pain in the ass hallway, with two sets of pain in the ass bifold doors, and with pain in the ass expensive carpet.
This is on a slab with copper radiant tube heat in the floor. I found where most of the tubes were at but I use the edger sander next to the original tack strip to give the second row of tack strip a good surface to stick to with a urethane adhesive.
The bifold doors were installed in unusual manner. The base pivots were on the slab not up on top of the carpet like you normally see them. The carpet I took up was a thick brick red carpet. I'm putting down a thin looped pile Masland carpet.
Customer wanted this done the same way so those lower guides do not show. The doors clearances we're okay when I took them off, so to make this work I did some very accurate measuring to the center of the holes in the guides.
The first photo shows two guides glued and screwed back to back. These two closets are side by side with a wall separating them. The wall separated to closet doesn't show when the doors are closed, so this was The logical way to make this work.
I got the carpet stretched in today so it's time to use my measurements and poke a nice neat round hole exactly centered in those guide holes.
I use this method before in a motorhome to actually burn a hole in the carpet for bolts to go through. You take a brass tube of the diameter you need, heated up with a propane torch till it's red hot, then use that to poke a nice neat hole where you want it. It melts the carpet and the backing and it's kind of like taking a core sample. In the process it also melts the carpet fibers in the backing together so it can't unravel.
The important thing is you have to absolutely 100% trust your measurements. Measure twice burn once.
The image with the torch in it has the brass rod that I use laying next to it. The pen is pointing at the hole.
The hallway had terracotta tile at the end of the hallway and going into a bathroom. Midway in the hall was an engineered wood floor that had to be tucked to. Both of the closets in the hall we're five and a half feet long and each one had to have a seam. Towards each end of the hallway will be doorway seams going into an office and a master bedroom. I'm going to start the office on Monday. Because I'm gluing the tack strip it's going to be a two-day job. I can't wait to get out of this one it's dragging on forever........ or I'm dragging it on forever.
This is on a slab with copper radiant tube heat in the floor. I found where most of the tubes were at but I use the edger sander next to the original tack strip to give the second row of tack strip a good surface to stick to with a urethane adhesive.
The bifold doors were installed in unusual manner. The base pivots were on the slab not up on top of the carpet like you normally see them. The carpet I took up was a thick brick red carpet. I'm putting down a thin looped pile Masland carpet.
Customer wanted this done the same way so those lower guides do not show. The doors clearances we're okay when I took them off, so to make this work I did some very accurate measuring to the center of the holes in the guides.
The first photo shows two guides glued and screwed back to back. These two closets are side by side with a wall separating them. The wall separated to closet doesn't show when the doors are closed, so this was The logical way to make this work.
I got the carpet stretched in today so it's time to use my measurements and poke a nice neat round hole exactly centered in those guide holes.
I use this method before in a motorhome to actually burn a hole in the carpet for bolts to go through. You take a brass tube of the diameter you need, heated up with a propane torch till it's red hot, then use that to poke a nice neat hole where you want it. It melts the carpet and the backing and it's kind of like taking a core sample. In the process it also melts the carpet fibers in the backing together so it can't unravel.
The important thing is you have to absolutely 100% trust your measurements. Measure twice burn once.
The image with the torch in it has the brass rod that I use laying next to it. The pen is pointing at the hole.
The hallway had terracotta tile at the end of the hallway and going into a bathroom. Midway in the hall was an engineered wood floor that had to be tucked to. Both of the closets in the hall we're five and a half feet long and each one had to have a seam. Towards each end of the hallway will be doorway seams going into an office and a master bedroom. I'm going to start the office on Monday. Because I'm gluing the tack strip it's going to be a two-day job. I can't wait to get out of this one it's dragging on forever........ or I'm dragging it on forever.
Attachments
Last edited: